We often encounter the concept of open drain and open collector in circuit design. What exactly are these two concepts? The following gives you a detailed introduction.
Open drain (opendrain) introductionThe "drain" mentioned in the open-drain circuit concept refers to the drain of the MOSFET. Similarly, the "set" in the open circuit refers to the collector of the triode. An open drain circuit is a circuit that uses the drain of a MOSFET as an output.
The "drain" mentioned in the concept of the open drain circuit refers to the drain of the MOSFET. Similarly, the "set" in the open circuit refers to the collector of the triode. An open drain circuit is a circuit that uses the drain of a MOSFET as an output. A common use is to add a pull-up resistor to the circuit outside the drain. The complete open drain circuit should consist of an open-drain device and an open-drain pull-up resistor. As shown below:
Circuit characteristics that make up the open drain1. Reduce the drive inside the IC by using the drive capability of the external circuit. When the internal MOSFET of the IC is turned on, the drive current flows from the external VCC through the Rpull-up, MOSFET to GND. Only a small gate drive current is required inside the IC.
2. It is possible to connect Pins of multiple open-drain outputs to one line. Form a "logical" relationship. As shown in Figure 1, when any of PIN_A, PIN_B, and PIN_C goes low, the logic on the open drain line is zero. This is also the principle that I2C, SMBus and other buses determine the bus occupancy status.
3. The transfer level can be changed by changing the voltage of the pull-up power supply. The logic level of the IC is determined by the power supply Vcc1, while the output high level is determined by Vcc2. This way we can control the output high logic with low logic.
4. Open-drain Pin is not connected to the external pull-up resistor, only low level can be output.
5. Standard open drain feet generally have only the ability to output. Add other judgment circuits to have the ability to input and output in both directions.
Introduction to opencollectorOpen-collector/Open-drain is a technology for bidirectional (Bi-direcTIonally) communication using multiple cables between multiple devices.
as the picture shows
Because Collector's pin is not connected to any other device, it is called Open Collector. The case of BJT is called Open-Collector, and the case of MOSFET is called Open-drain. In theory, BJT is the same as MOSFET.
When the input has a high signal, the transistor is ON. At this time, Output and Groud form a path to make the Output output Low.
When the input has a low signal, the transistor is OFF, and the Output is in the Hi-inpedence state.
Hi-impedence means a state in which the impedance is high and Low and High cannot be distinguished.
ZGAR Aurora 1800 Puffs
ZGAR electronic cigarette uses high-tech R&D, food grade disposable pod device and high-quality raw material. All package designs are Original IP. Our designer team is from Hong Kong. We have very high requirements for product quality, flavors taste and packaging design. The E-liquid is imported, materials are food grade, and assembly plant is medical-grade dust-free workshops.
Our products include disposable e-cigarettes, rechargeable e-cigarettes, rechargreable disposable vape pen, and various of flavors of cigarette cartridges. From 600puffs to 5000puffs, ZGAR bar Disposable offer high-tech R&D, E-cigarette improves battery capacity, We offer various of flavors and support customization. And printing designs can be customized. We have our own professional team and competitive quotations for any OEM or ODM works.
We supply OEM rechargeable disposable vape pen,OEM disposable electronic cigarette,ODM disposable vape pen,ODM disposable electronic cigarette,OEM/ODM vape pen e-cigarette,OEM/ODM atomizer device.
Aurora 1800 Puffs,Pod System Vape,Pos Systems Touch Screen,Empty Disposable Vape Pod System,1800Puffs Pod Vape System
ZGAR INTERNATIONAL(HK)CO., LIMITED , https://www.zgarvapor.com