PCB design specifications for LED switching power supplies

In any switching power supply design, the physical design of the PCB is the last link. If the design method is not correct, the PCB may radiate too much electromagnetic interference, causing the power supply to be unstable. The following points are required for each step. analysis:

First, from the schematic diagram to the PCB design process to establish component parameters -> input principle netlist -> design parameter settings -> manual layout -> manual wiring -> verification design -> review -> CAM output.

Second, the parameters set adjacent conductor spacing must be able to meet electrical safety requirements, and for ease of operation and production, the spacing should be as wide as possible. The minimum spacing should be at least suitable for the voltage to withstand. When the wiring density is low, the spacing of the signal lines can be appropriately increased. The signal lines with high and low levels should be as short as possible and the spacing should be increased. Under normal circumstances Set the trace spacing to 8 mils.

The distance from the edge of the pad to the edge of the board is greater than 1mm, which avoids pad defects during processing. When the traces connected to the pads are thinner, the connection between the pads and the traces is designed to be water droplets. This has the advantage that the pads are not easy to peel, but the traces are not easily disconnected from the pads.

Third, the component layout practice proves that even if the circuit schematic design is correct and the printed circuit board is not properly designed, it will adversely affect the reliability of the electronic equipment. For example, if the two thin parallel lines of the printed board are close together, the delay of the signal waveform will be formed, and the reflection noise will be formed at the end of the transmission line; the interference caused by the inconsistency of the power supply and the ground line will cause the product to be Performance is degraded, so when designing a printed circuit board, care should be taken to use the correct method. Each switching power supply has four current loops:

(1). Power switch AC circuit

(2). Output rectifier AC circuit

(3). Input signal source current loop

(4). Output load current loop The input loop charges the input capacitor through an approximately DC current. The filter capacitor mainly acts as a broadband energy storage; similarly, the output filter capacitor is also used to store the high frequency energy from the output rectifier. At the same time, the DC energy of the output load loop is eliminated. Therefore, the terminals of the input and output filter capacitors are very important. The input and output current loops should be connected only from the terminals of the filter capacitor to the power supply; if the connection between the input/output loop and the power switch/rectifier loop cannot be connected to the capacitor The terminals are directly connected and the AC energy is radiated from the input or output filter capacitors to the environment. The AC circuit of the power switch AC loop and rectifier contains high amplitude trapezoidal currents. The harmonic components of these currents are very high. The frequency is much higher than the fundamental frequency of the switch. The peak amplitude can be up to 5 times the amplitude of the continuous input/output DC current. The transition time is usually It is about 50ns. These two loops are the most susceptible to electromagnetic interference, so these AC loops must be placed before other traces in the power supply. The three main components of each loop are filter capacitors, power switches or rectifiers, inductors or transformers. Place them adjacently and adjust the position of the components so that the current path between them is as short as possible. The best way to establish a switching power supply layout is similar to its electrical design. The best design flow is as follows:

Place transformer

Designing the power switch current loop

Design output rectifier current loop

Control circuit connected to the AC power circuit

Design input current source loop and input filter design Output load loop and output filter According to the functional unit of the circuit, the following principles should be met when laying out all the components of the circuit:

(1) First consider the PCB size. When the PCB size is too large, the printed lines are long, the impedance is increased, the noise resistance is reduced, and the cost is also increased; if the size is too small, the heat dissipation is not good, and the adjacent lines are susceptible to interference. The optimal shape of the board is rectangular, with an aspect ratio of 3:2 or 4:3. The components at the edge of the board are generally not less than 2mm from the edge of the board.

(2) Consider the future soldering when placing the device, not too dense.

(3) Center around the core components of each functional circuit and arrange it around it. Components should be evenly, neatly and compactly arranged on the PCB to minimize and shorten leads and connections between components. The decoupling capacitors should be as close as possible to the VCC of the device.

(4) For circuits operating at high frequencies, the distribution parameters between components should be considered. In general, the circuit should be arranged in parallel as much as possible. In this way, it is not only beautiful, but also easy to load and weld, and easy to mass produce.

(5) Arrange the position of each functional circuit unit according to the flow of the circuit, so that the layout facilitates signal circulation and keeps the signal as consistent as possible.

(6) The first principle of the layout is to ensure the routing rate of the wiring. Pay attention to the connection of the flying wires when moving the device, and put the devices with the connected relationship together.

(7) Reduce the loop area as much as possible to suppress radiated interference from the switching power supply.

Casters

We are professional manufacturer of various kinds of casters .The most professional production, the most safe and durable caster is that we adhere to the concept of High Quality and Mutual Benefit

With casters production enterprises of since its inception, specializing in the production of industrial casters, scaffolding caster for 20 years. In the past 20 years, we have rich experience in design and production standards, won a good reputation at home and abroad. With casters to customers in North America, Europe, Asia, Australia, South Africa and the Middle East, we experience also let us understand the needs of the international market, fast delivery and safe use. The company has 150 units/sets of production equipment, 2 pouring PU production line, 2 rubber vulcanization production line , 10 sets of large-scale injection molding equipment, automatic welding equipment, equipped with professional level of production to modernize. Using the fully and semi-automatic machinery to achieve excellence in technology and the production of consistency; Research and development team using advanced CAD/CAM software and three-dimensional software design OEM caster; Equipped with professional mold development workshop, by professional engineers to adjust the existing model, constantly updated design, so as to adapt to the changing demands of customers at home and abroad; By professional personnel in accordance with the strict product inspection standards for all products are factory inspection, to ensure the high quality of the products.

We produce PU casters and rubber casters, high bearing capacity, the use of lightweight flexible, but won't hurt smooth floor .Special process increases the stability and the security of the load, the high quality raw materials and advanced processing technology, ensure with casters do not come unglued, no crack, more wear-resisting ;Processing with galvanized metal stents or plastic spraying Metal , make the caster wheel bracket is not easy to rust.

Light Duty Casters,Lower Gravity Casters,Medium Heavy Casters,Industrial Casters,Extra Heavy Duty Casters,Shock Absorb Casters,Mute Casters

BAODING JIMAOTONG IMPORT AND EXPORT CO., LTD , https://www.chinagroundscrew.com

Posted on