The topic of anti-interference of DC-DC converters will be discussed in detail here. Let's talk about DC-DC converters. Since the birth of electronics, there is an old saying... "All problems are DC problems."
Of course, DC refers to "direct current", that is, a unidirectional current passing through a conductor from point A to point B in a circuit. We know that the "problem" mentioned here is very simple, that is... the problem. So why are all issues DC issues?
We know that current and electrons are simply the energy produced by currents in various conductors and devices in a complete circuit system. Therefore, in the final analysis, it is an energy conversion. Energy is the ability to do work in two forms: 1) potential energy and 2) kinetic energy. Potential energy is an inactive energy storage (such as the voltage between battery terminals). Kinetic energy is the energy generated when potential energy is converted into an active state (such as current flowing through a bulb). Electronics is simply the science of transforming potential energy (voltage) into kinetic energy (current) by controlling the current in various conductors! Ohmic 'DC Law' must always satisfy the energy conversion to make a difference! Therefore, each part of the circuit input and output, whether or not with AC function, must be well designed for the DC structure of the circuit to effectively support any form of energy conversion. In other words, if the circuit DC design is poor, it is impossible to achieve AC performance.
This situation puts great pressure on the designer, and needs to master the high-level expertise in multidisciplinary fields based on the “simulation design†between the power supply and the ground. In order to convert direct current (DC) with low noise under various voltage conditions with respect to various input signals, it is first necessary to select the correct DC-DC converter. DC-DC converters come in a variety of sizes and types: converters include linear, switch mode, and magnetoelectric. Moreover, the boost (step-up) and buck (step-down) functions use a variety of energy conversion circuits. Knowing these circuit types correctly can avoid performance degradation when used. Later, we can analyze the devices introduced by industry leaders, such as the National Semiconductor's recently launched Simple Switcher power module.
"All problems are DC problems..." Knowing this when considering DC-DC converters can lay the foundation for good circuit design.
Linear regulator
Linear regulators are the most basic components of all DC-DC converters. The linear regulator is a voltage regulator that operates in a "linear region" relative to a switching regulator operating in the "non-linear" switching mode region (which we will discuss later). The linear regulator must meet the rated power supply for the load (low noise to an acceptable level) while reducing the output impedance requirements so that the voltage gain is not affected by the load impedance value. The linear regulator acts as a variable resistor that regulates the voltage divider network to maintain a constant output voltage while providing various load currents.
figure 1
Figure 1 shows the schematic of the linear regulator. The figure shows a "series" linear regulator circuit because the regulation device (transistor Q) is in series with the load R2. The circuit regulates the Zener diode DZ output voltage (because the transistor base current is a small fraction of the Zener to R1 bias current). The transistor emitter output voltage is one diode drop below the Zener voltage and has sufficient current gain to drive the high output value Iout (via R2). Although the circuit has good output voltage regulation (as long as Q is operating in the linear region), it still senses load, power supply variable (Vs), noise, and power supply ripple. Some of these problems can be solved with a negative feedback circuit sensing circuit output. At other times, this circuit is often used as a voltage reference to support more advanced linear regulator designs. When designing or selecting a linear regulator, you must also carefully consider the electrical noise, the ripple generated by the power supply Vs to Vout, and the common-mode voltage that may be coupled in the regulator output.
For example, when selecting a linear regulator, the circuit power requirements and regulator output characteristics must be carefully determined. Take National Semiconductor's LM340/LM78XX series of three-terminal positive voltage regulators as an example. These linear regulators are standard devices with basic design elements in the industry. In general, some devices specify a fixed output voltage at a fixed input voltage (typically Vs-Vout > 2V) and a maximum fixed output load current Iout.
Wuxi Motian Signage Co., Ltd , https://www.makesignage.com